+8618974971540

Application of coated tools in high-speed dry cutting

Jul 28, 2021

Application of coated tools in high-speed dry cutting


        Cutting is a commonly used processing technology in mechanical processing. With the development and progress of technology, people have put forward higher requirements for traditional cutting processing such as high speed and cleanliness, which has a great impact on certain processes that rely on the use of cutting fluid for processing. However, technology is constantly improving and progressing. Today, cutting fluid is no longer a necessary factor in machining. One of the important reasons is the use of coated tools. Cutting tool

  Coated tool in the process of processing, by inhibiting the heat transfer from the cutting area to the insert (tool) to slow down the temperature impact. The coating acts like a thermal barrier because it has a much lower thermal conductivity coefficient than the tool base and workpiece material.

Therefore, these tools absorb less heat and can withstand higher cutting temperatures. Whether it is turning or milling, coated tools allow the use of more efficient cutting parameters without reducing tool life. Boring tool manufacturer

  The thickness of the coating is between 2 and 18m, and it plays an important role in the performance of the tool. Thinner coatings can withstand temperature changes better than thicker coatings during impact cutting. This is because thinner coatings have less stress and are less prone to cracks. During rapid cooling and heating, the thick coating is like a glass that is heated and cooled extremely quickly, and is easily broken. Dry cutting with thin-coated inserts can extend tool life by up to 40%, which is why physical coatings are often used to coat round tools and milling inserts. PVD coatings tend to be thinner than chemical coatings and are more firmly bonded to the contours. In addition, PVD coatings can be deposited on cemented carbide at much lower temperatures. Therefore, they are more used for very sharp cutting edges and large positive rake angle milling cutters and turning tools.

       Although the coating material titanium nitride occupies 80% of all coated tools. However, in the case of high-speed dry cutting, the best PVD coating is TiAlN. Its performance is four times better than titanium nitride in high-temperature continuous cutting, such as for high-speed turning. TiAlN coating is also better than other coatings for tools under higher thermal stress conditions. Such as dry milling and deep hole drilling of small diameter holes where cutting fluid is difficult to reach. Lathe tool

  TiAlN is harder than TiN at cutting temperature and has thermal stability. The PVD coating takes advantage of its chemical wear resistance. Its hardness is as high as 3500 degrees Vickers, and its working temperature is as high as 1470°F (800°C). Materials scientists speculate that these properties can be attributed to the amorphous aluminum oxide film, which is formed at the chip/tool interface after some aluminum in the coating surface is oxidized at high temperatures.

         This research deliberately selected ultra-thin multi-layer PVD coatings. The coatings produced by this deposition process consist of hundreds of layers, each of which is only a few nanometers thick. The deposits of general PVD coatings are only a few layers of micron-thickness coatings.

        Although PVD coating has many advantages, CVD coating is still more popular for processing most ferrous metals. In the CVD process, a higher deposition temperature helps to improve the bonding strength, and allows a higher cobalt content in the matrix, so that the toughness of the blade is good, and the ability to resist plastic deformation is improved. Since CVD coatings are thicker than PVD coatings, passivation is required at their cutting edges to prevent the coating from peeling off, and it can also help improve the wear resistance of the tool. The allowable feed rate can reach 0.035 inches/revolution (0.9mm/r). Boring tool manufacturer

  CVD is a process of depositing a useful layer of aluminum oxide on the cutting tool, which is the most heat-resistant and oxidation-resistant coating known. Alumina is a poor conductor. It separates the tool from the heat generated by cutting deformation and encourages the heat to flow into the chips. This is an excellent CVD coating material, mainly used for cemented carbide turning tools used in dry cutting. It can also protect the substrate during high-speed cutting, and is the best coating that resists abrasive wear and crater wear.


Send Inquiry